• 大家都在搜: 不锈钢酒店装饰玻璃空透隔断 不锈钢金属工程玄关走道屏风 不锈钢酒店装饰中式屏风 不锈钢金属工程不锈钢橱柜 不锈钢花纹屏风镀钛
  • 18763996167


  • 全国咨询热线
联系我们
服务热线
18763996167
座机:0531-88275278 
邮箱: 279546205@qq.com
地址:山东省济南市天桥区大桥街道办事处倪家村136号
当前位置:首页-新闻资讯>公司动态>不锈钢酒店装饰之橱柜的制作

不锈钢酒店装饰之橱柜的制作

来源:http://www.sdshbxg.com 日期:2020-04-29 发布人:admin
在中密度基板上采用镂铣的方式形成图案,再用吸塑的方法在不锈钢橱柜上覆以PVC,就形成PVC吸塑模压不锈钢橱柜。吸塑加工制作工艺流程是:裁板-打孔-铣型-磨-喷胶-覆膜(PVC)-边。
On the medium density base plate, the pattern is formed by cutting and milling, and then the stainless steel cabinet is covered with PVC by the method of Blister molding, forming the PVC Blister molding stainless steel cabinet. The technological process of Blister processing is: cutting, punching, milling, grinding, spraying and laminating (PVC) - edge.
1.裁板:根据不锈钢橱柜尺寸裁板,裁板后的长与高尺寸均要减去两层PVC的厚度(约0.5mm)。
1. Cutting board: cut the board according to the size of stainless steel cabinet. The length and height of the cut board should subtract the thickness of two layers of PVC (about 0.5mm).
2.打孔:打铰链孔要做吸塑热架,打铰链孔时特别要注意左右方向。
2. Punching: to punch the hinge hole, we need to make a blister hot frame, and pay special attention to the left and right directions when punching the hinge hole.
3.铣型:根据门型规格进行镂铣,在镂铣前必须正确地选择刀具,由于刀具的转速达到20000r/min,所以,镂铣前必须将刀具牢牢固定,不能有丝松动。不锈钢橱柜的铣型必须做到横平竖直.转弯处圆弧连接要自然且深浅一致。
3. Milling type: the cutting tool must be selected correctly before the milling according to the door type specification. Since the rotation speed of the cutting tool reaches 20000r / min, the cutting tool must be firmly fixed before the milling, and there shall be no loose wires. The milling type of stainless steel cabinet must be horizontal and vertical. The arc connection at the turning should be natural and consistent in depth.
不锈钢酒店装饰
4.打磨:不锈钢橱柜打磨是很重要的一道工序,其效果直接影响不锈钢橱柜的外观质量。打 磨时先用粗砂将机加工留下的痕迹磨掉.然后用细砂精磨.保证不锈钢橱柜无划痕平整光滑,特别在转角过渡处必须自然圆滑。精砂磨好后还要检查板面有无气孔凹痕,如有。可使川50胶水填充烘干,砂磨达到完全平核。
4. Grinding: stainless steel cabinet grinding is a very important process, its effect directly affects the appearance quality of stainless steel cabinet. During grinding, the marks left by machining shall be ground off with coarse sand first, and then finely ground with fine sand to ensure that the stainless steel cabinet is free of scratches, flat and smooth, especially at the corner transition, it must be natural and smooth. After fine sanding, check whether there are air holes and dents on the board surface, if any. It can make the chuan50 glue filled and dried, and the sand mill can reach a complete flat core.
5.喷胶:用胶量必须适,且喷涂均匀,喷胶用的压缩空气必须经过油水分离装置过滤.保证喷胶的质量。
5. Glue spraying: the amount of glue must be suitable and evenly sprayed. The compressed air for glue spraying must be filtered by the oil-water separation device to ensure the quality of glue spraying.
6.覆膜(PVC):不锈钢橱柜在放人吸塑机前.必须严格检查喷胶面有无细微的硬胶粒。当薄膜覆盖在不锈钢橱柜上时.吸塑工作台四周必须压紧,防止漏气,再将吸塑工作台推进真空室加温、抽真空。在操作时必须严格控制真空室的工作温度和真空压力泵的压力。
6. Laminating (PVC): stainless steel cabinet must be strictly inspected for fine hard rubber particles on the spray surface before putting it into the plastic suction machine. When the film is covered on the stainless steel cabinet, the plastic suction table must be tightly pressed around to prevent air leakage, and then the plastic suction table is pushed into the vacuum chamber for heating and vacuumizing. During operation, the working temperature of the vacuum chamber and the pressure of the vacuum pressure pump must be strictly controlled.